Powered by Max Banner Ads 

My office has a plethora of bikes that live full– or part–time in the warehouse. This small fleet of communal cruisers and commuter bicycles needed an organized home rather than randomly strewn about the room.

Luckily, we have a couple of industrious fellas who took on the task of building a bike rack with limited funds, two wooden pallets, and an hour to spare. Now we’re sharing with you the step-by-step guide on how to build your own hanging bike rack.

Build Your Own Bike Rack

WHAT YOU’LL NEED:

Materials

  • Two ~6’ tall wooden pallets (or five 6′ 2x4s, plus one 8′ 1×6 and one 8′ 1×4)
  • Wood screws (We used Grabber screws #8 x 2.5” and #9 x 3”)
  • Bicycle or storage hooks

Tools

  • Power drill
  • Power saw
  • Hammer

BYOBR Equipment

Building buddy!
Grab a friend or two. The building will be easier, safer, and more fun with a friend.

BYOBR Parker & Will

STEP ONE
Carefully disassemble the two pallets and remove all nails––this is where the hammer comes in handy. Group the pallet lumber into similarly sized pieces. All the longest, sturdiest pieces (the 2x4s) will form the frame of the bike rack.

BYOBR Wood Pallet Parts

BYOBR Pallet Pieces

STEP TWO
Construct the frame using five of the 2x4s. You may need to trim some of the lumber to size as Will & Parker did for our bike rack.

BYOBR Frame

Secure each corner with two long wood screws.

BYOBR Building Frame

The bottom beam usually needs to be the flattest, least likely to wobble; however, the bottom beam on the rack built by Parker & Will was warped. Gotta work with what you have.

STEP THREE
You should now have a large rectangle. Place the third and remaining 2×4 directly in the middle between the two outer columns. You can see how carefully Will measures the distance using the highly-scientific “counting-his-steps” method.

BYOBR Measuring Frame copy

You may need to trim the lumber to size. Secure the middle column with two screws at either end.

BYOBR Building Frame 2

BYOBR Frame Raised

STEP FOUR
Give this rack some feet to stand on! Secure a 1×6 to the base of the outer columns with four screws each.

BYOBR Adding Feet

BYOBR Adding Feet 2

STEP FIVE
Bracer. Create a stabilizer for each foot––’cause you know triangles are the strongest shape (I learned that in 3rd Grade).

BYOBR Feet Added

Parker identified the angle for the cut by holding the 1×6 in place and marking with his favorite mechanical pencil. Super sophisticated stuff here.

BYOBR Measuring Cuts

Trim each stabilizing piece along the identified angles, so that the edges are flush with the frame.

BYOBR Preparing Cuts

Secure each brace with a couple screws.

BYOBR Adding Stabilizers

BYOBR Stabilizers

STEP SIX
More stabilizers! Add a small 1×4 stabilizer at each corner of frame for added stability. That’s four in total, if you’re counting.

BYOBR Top Stabilizers

Measure and cut the smaller stabilizers using the same method in Step Five. IMPORTANT: Don’t place your stabilizers too far into the frame or they may obstruct how your bikes hang. Secure with the smaller length screws.

BYOBR Parker Drilling

Lookin’ good! You’re almost there.

STEP SEVEN
Evenly space four bicycle hooks into the frame. Leave plenty of elbowroom for your bikes’ handlebars. Hint: it helps if you drill a starter hole before screwing the hooks into place. (Look at the teamwork happening!)

BYOBR Will & Parker Adding Hooks

STEP EIGHT
Hang up yo’ bikes! Stand back and admire a job well (and economically) done.

BYOBR Will hanging up bikes

BYOBR Completed Bike Rack

BYOBR Completed Bike Rack 2